Husqvarna iZ4217SKAA User Manual

Operators manualModels:Please read these instructions carefully and makesure you understand them before using the machine.MANUAL NO. 539108877 REV. IR

10SAFETY INSTRUCTIONSChildren:• Serious accidents may occur if you fail to beon guard for children in the vicinity of the ma-chine. Children are often

11• Allow the engine to cool before refueling. Donot smoke. Do not fill fuel in the vicinity ofsparks or open flames.• If leaks arise in the fuel syst

12• Never use the machine indoors or in spaceslacking proper ventilation. The exhaust fumescontain carbon monoxide, and odorless, poi-sonous, and leth

13PRESENTATIONPresentationThank you for buying a HUSQVARNA! Beforeoperating your new mower, read, understandand follow the safety instructions and oth

14SETUP AND ADJUSTMENTSWARNING: No settings or adjustments areto be made unless: Engine is stopped, keyhas been removed, park brake is on andbattery c

15SETUP AND ADJUSTMENTSMower Deck LevelingPosition machine on a flat surface. Preferablylevel concrete.Check the tire pressure in all four tires. Infl

16Motion Control Linkage AdjustmentThis adjustment must be made with the rearwheels rotating. Raise the rear of the machineand block it up so the whee

17Run engine full throttle to make sure wheels donot rotate. Readjust if any rotation occurs.Repeat the whole process for the opposite sideand tighten

18By moving the levers an equal amount forwardor back the machine will move in a straight linein that direction. FIG - 9Movement of either lever forwa

19Fuel shut off valve is located at the right rear of theseat. The valve has three positions a right tank, lefttank and center is the off position. FI

2©2003 Husqvarna. All right reserved.Beatrice, NE. Printed U.S.A.

20HardwareCheck daily. Inspect the entire machine forloose or missing hardware.Air filterSee engine manufacturers specifications forcleaning and repla

21MAINTENANCEPump beltCheck belt every 100 hours for excessive wear.To replace belt. Relieve tension on the deck beltand remove deck belt from clutch.

22Torque Specifications· Engine crankshaft bolt 67 Nm(50 ft/lb)· Deck pulley bolts 61 Nm (45 ft/lb)· Hydraulic tube nuts 41 Nm (30 ft/lb)· Wheel motor

23Maintenance ScheduleFor iZ RidersMaintenance Maintance Interval (hours)Daily 25 50 100 200 250 500Engine (4)Check oil level XChange oil and filter (

24TROUBLE SHOOTINGPROBLEM POSSIBLE CAUSESENGINE WILL NOT START.Blade switch on.Drive levers not in the neutral slots.Operator not in seat.Park brake d

25WIRING DIAGRAMSCONSOLE HARNESSFrameHarnessEngineClutchLeftMotionControlHourMeterBladeSwitchSeatStarterSwitchRightMotionControlP/N104414

26WIRING DIAGRAMSCONSOLE HARNESS SCHEMATIC

27FRAME HARNESSWIRING DIAGRAMSClutchEnginePigtailGround toEngineStarterSolenoidParkBrakeConsoleHarnessBrakeRelayStartRelayRunRelayP/N104964

28WIRING DIAGRAMSFRAME HARNESS

29

3CONTENTSINTRODUCTION ... 4SYMBOLS & DECALS ... 6SAFETY INSTRUCTIONS ... 7Ge

4INTRODUCTIONIntroductionCongratulationsThank you for purchasing a Husqvana ride-on mower. This machine is built for the greatest effi-ciency and rapi

5INTRODUCTIONGood ServiceHusqvarna’s products are sold all over the world and only in specialized retail stores with completeservice. This ensures tha

6SYMBOLS AND DECALSSymbols and DecalsThese symbols are found on the machine and in the operator’s manual.Study them carefully so that you know what th

7SAFETY INSTRUCTIONSSafety InstructionsThese instructions are for your safety. Read them carefully.WARNING!This symbol means that important safety ins

8SAFETY INSTRUCTIONS• Be careful when rounding fixed objects, so thatthe blades do not hit them. Never drive overforeign objects.• Only use the machin

96003-004Mow up and down, not side-to-side.Driving on SlopesSAFETY INSTRUCTIONSDriving on slopes is one of the operations wherethe risk is greatest th