Husqvarna P 525D User Manual

EEEEnnnngggglllliiiisssshhhh P 520D P 525D Oper ator ′ s manual Please r ead the operator’s manual carefully and make sure you understand the instr

10 – EnglishSAFETY INSTRUCTIONSChildren• Serious accidents may occur if you fail to be on your guard for children in the vicinity of the machine. Chil

English – 11SAFETY INSTRUCTIONS• Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting.• Never m

12 – EnglishPRESENTATIONPresentationCongratulations on your choice of an excellent quality product that will give you great pleasure for many years. T

English – 13PRESENTATIONAdjusting the cutting heightThe cutting height can be adjusted to seven different positions.Select the required cutting height

14 – EnglishPRESENTATIONSeatThe seat has a jointed attachment on the front edge and can be tipped forward.To fold the seat forward, the latch for the

English – 15PRESENTATIONThe power outlet is switched on and off using power switch on the control panel.The power outlet works even if the ignition is

16 – EnglishPRESENTATIONROPS (Roll Over Protective Structure)ROPS is a protective frame that reduces the risk of injury in the event of overturning. U

English – 17STARTING ENGINEBefore starting• Read the safety instructions and information concerning the placement of controls and functions before sta

18 – EnglishSTARTING ENGINEStarting the engine with a weak batteryIf the battery is too weak to start the engine, it should be recharged.When jump lea

English – 19DRIVINGDriving the Rider1 Release the parking brake before driving2 Carefully press down one of the pedals until the required speed is obt

2 – English CONTENTS Contents CONTENTS Contents ... 2 Ser vice journal Pre-deli

20 – EnglishDRIVINGCutting tips• Localise and mark stones and other fixed objects to avoid collision.• Start with a high cutting height and reduce dow

English – 21MaintenanceMaintenance scheduleThe following is a list of the maintenance which should be conducted on the machine. For those points not d

22 – EnglishMaintenanceCleaningClean the machine directly after use. It is much easier to wash off grass cuttings before they dry.Oily dirt can be rem

English – 23MaintenanceAdjustment of pump and alternator belt• Loosen the lower mounting screw and upper adjustment screw a few turns.• Tension the be

24 – EnglishMaintenanceThe main filter has a paper insert that is changed as follows.1 Open the engine cover.2 Unscrew the filter cover and remove the p

English – 25MaintenanceCheck the safety systemThe machine is equipped with a safety system that prevents starting or driving under the following condi

26 – EnglishMaintenanceCheck the batteryThe machine is equipped with a maintenance-free battery. The battery has a service window showing different co

English – 27Maintenance9 Remove the service hatch.10 Fit the rear universal drive shaft.11 Fit the locking chain to the universal joint cover around t

28 – EnglishMaintenanceService position for the cutting unitThe cutting head can be placed in the service position to provide easy access for cleaning

English – 29Maintenance12 Secure the cutting unit with the safety belt, which is stored in the storage compartment under the seat.Restoring from servi

English – 3 Ser vice journal Pre-deliver y service 1 Charge the battery for at least 4 hours at max. 3 amp. 2 Check coolant level and antifreeze.3

30 – EnglishMaintenanceTilt angle• Place the machine on a flat surface.• Check the tyre pressures. The tyre pressure should be 1.5 bar/150 kPa/22 PSI f

English – 31MaintenanceAdjustment of PTO belts1 Tighten screw (4) until the sleeve bottoms against the frame bracket. Tighten lock nut (3) whilst hold

32 – EnglishMaintenanceChange coolantCorrect coolant level is important for the cooling system to function properly. Therefore the coolant level must

English – 33LubricationLubrication scheduleLegend for the lubrication schedule Filter replacement Oil change Level check Grease nipple Oil can Check b

34 – EnglishLubricationAccessoriesLubrication or other maintenance of optional equipment or accessories is not described in this manual. This equipmen

English – 35LubricationThe drive shaft front support bearingLubricate with a grease gun until the grease is forced out. The drive shaft rear support b

36 – EnglishLubricationThe following oil classes are recommended:• API Service Class: CH4 or ACEA E5 or higher.Choose an oil with viscosity according

English – 37LubricationCheck the oil level in the transmission gearboxes• Use the oil dipstick to check that there is oil in the transmission.• The oi

38 – EnglishTroubleshooting scheduleProblem ProcedureEngine does not start There is no fuel in the fuel tankAir in fuel systemIncorrect fuel typeIgnit

English – 39Troubleshooting scheduleEngine overheats Engine overloadedCoolant level too lowAir intake or cooling flanges blockedFan damagedToo little o

4 – English INTR ODUCTION Dear Customer , Thank y ou for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a front-mou

40 – EnglishELECTRICAL SYSTEMNumbers correspond to:1 Switch for the lights2 Instrument panel3 Lights4 Counter5 Ignition lock6 Inductive sensor, parkin

English – 41ELECTRICAL SYSTEMWiring diagram P 520D

42 – EnglishELECTRICAL SYSTEM

English – 43ELECTRICAL SYSTEM

44 – EnglishELECTRICAL SYSTEM

English – 45ELECTRICAL SYSTEM

46 – EnglishELECTRICAL SYSTEM

English – 47ELECTRICAL SYSTEMWiring diagram P525 D

48 – EnglishELECTRICAL SYSTEM

English – 49ELECTRICAL SYSTEM

English – 5 INTR ODUCTION Good ser vice Husqv arna products are sold all over the world and ensures that you, the customer, get the best support an

50 – EnglishELECTRICAL SYSTEM

English – 51ELECTRICAL SYSTEM

52 – EnglishELECTRICAL SYSTEM

English – 53StorageWinter storageAt the end of the season, or if the machine is going to stand idle for more than 30 days, it should immediately be ma

54 – EnglishTECHNICAL DATANote 1: The power rating of the engine indicated is the average net output (at specified rpm) of a typical production engine

English – 55TECHNICAL DATANote 2: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/EC.Note 3:

´®z+Vsh¶6}¨2012-04-12´®z+Vsh¶6}¨1154837-26Original instructions

6 – English KEY T O SYMBOLS Symbols These symbols are on the machine and in the instr uctions.WARNING! Careless or incorrect use can result in ser

English – 7 WHA T IS WHA T? Location of the contr ols123456789101112131415181916 17202122232425 1 Knob for seatback angle2 Throttle trigger3 Power

8 – English SAFETY INSTR UCTIONS Saf ety instructions These instr uctions are for your safety. Read them carefully. Insure y our Rider • Check the

English – 9 SAFETY INSTR UCTIONS • Never allow children or other persons not trained in the use of the machine to use or service it. Local laws may