EEEEnnnngggglllliiiisssshhhh 324R X-Series Oper ator’s manual (EPA) Please r ead the operator’s manual carefully and make sure you understand the inst
GENERAL SAFETY PRECAUTIONS10 – EnglishLocking nutA locking nut is used to secure some types of cutting attachment.When fitting, tighten the nut in the
GENERAL SAFETY PRECAUTIONSEnglish – 11General rulesOnly use cutting attachments with the guards we recommend! See the chapter on Technical data.Keep t
GENERAL SAFETY PRECAUTIONS12 – English• The filing angle is 15°. File alternate teeth to the right and those in between to the left. If the blade has b
ASSEMBLYEnglish – 13Fitting the handlebar• Remove the screw at the rear of the throttle handle.• Slide the throttle handle onto the right side of the
ASSEMBLY14 – EnglishAssembling the cutting equipmentFitting a blade guard, grass blade and grass cutter• Hook the blade guard/combination guard (A) on
ASSEMBLYEnglish – 15CAUTION! Use the recommended blade guard. See the Technical data section.• Fit the drive disc (B) on the output shaft.• Turn the b
ASSEMBLY16 – English• Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half ali
ASSEMBLYEnglish – 17Correct heightAdjust the shoulder strap so that the cutting attachment is parallel to the ground.Correct balanceLet the cutting at
FUEL HANDLING18 – EnglishFuel handlingNever start the machine:1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evap
FUEL HANDLINGEnglish – 19When the oil level is low, top up using engine oil to the edge of the oil refill hole.Only use recommended engine oil.FuelingC
KEY T O SYMBOLS 2 – English Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in s
STARTING AND STOPPING20 – EnglishCheck before starting• Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the cent
STARTING AND STOPPINGEnglish – 21Choke: Set the choke control in the choke position. Primer bulb: Press the air purge repeatedly until fuel begins to
WORKING TECHNIQUES22 – EnglishGeneral working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot
WORKING TECHNIQUESEnglish – 23The ABC of clearing• Always use the correct equipment.• Make sure the equipment is well adjusted.• Follow the safety pre
WORKING TECHNIQUES24 – English• You should plan the strip so that you avoid going over ditches or other obstacles on the ground. You should also orien
WORKING TECHNIQUESEnglish – 25Brush cutting with a saw blade• Thin stems and brush are mown down. Work with a sawing movement, swinging sideways.• Try
WORKING TECHNIQUES26 – EnglishCutting• The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord paral
MAINTENANCEEnglish – 27CarburetorFunction• The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carbureto
MAINTENANCE28 – EnglishCooling systemTo keep the working temperature as low as possible the machine is equipped with a cooling system.The cooling syst
MAINTENANCEEnglish – 29Oiling the air filterAlways use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread e
CONTENTS English – 3 Contents Note the f ollowing before starting: Please read the oper ator’s manual carefully.Maintenance, replacement, or repai
30 – EnglishMAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des
English – 31TECHNICAL DATATechnical dataNote 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure lev
32 – EnglishTECHNICAL DATA324RxApproved accessories Type Cutting attachment guard, Art. no.Arbor shaft thread M10Grass blade/grass cutterGrass 255-4 (
FEDERAL EMISSION CONTROL WARRANTY STATEMENTEnglish – 33YOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme
1Super Auto IISuper Auto II 123456789104,0 m 13'2,4 mm.095"~2,0 m6,5'6"6""15 cm15 cm
"Clic"12356710118,5 m28'484,2 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cmS35
12432,4-2,7 mm.095-.106"4,25 m14'4,25 m14'B6"15 cmA6"15 cmS355
T35, T35x"Clic"12356798,5 m28'484,3 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cm
4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates b
1150262-95´®z+R:=¶5I¨´®z+R:=¶5I¨2008-03-31
English – 5 WHA T IS WHA T? What is what on the c learing saw? 1 Blade2 Grease filler cap, bevel gear3 Bevel gear4 Cutting attachment guard5 Shaft6
GENERAL SAFETY PRECA UTIONS 6 – English Impor tant Personal protective equipment HELMET A helmet should be w orn if the trees being cleared are tal
GENERAL SAFETY PRECA UTIONS English – 7 BOO TSWear boots with steel toe-caps and non-slip sole.CLOTHINGWear clothes made of a strong fabric and av
GENERAL SAFETY PRECA UTIONS 8 – English then the carb urettor idle setting must be checked. See instructions under the heading Maintenance. Stop s
GENERAL SAFETY PRECAUTIONSEnglish – 9Quick releaseThere is an easily accessible, quick release fitted at the front as a safety precaution in case the e
Comments to this Manuals