Husqvarna LTH140 User Manual download pdf (Page 9)

ASSEMBLY

ASSEMBLE GAUGE WHEELS TO MOWER

DECK (See Fig. 7)

Assemble gauge wheels with tractor on a flat level surface.

• Adjust mower to desired cutting height (See “TO AD-

JUST MOWER CUTTING HEIGHT” in the Operation

section of this manual).

• With mower in desired height of cut position, gauge

wheels should be assembled so they are slightly off the

ground. Install gauge wheel in appropriate hole with

shoulder bolt, 17/32 washer, 3/8 washer, and 3/8-16

locknut and tighten securely.

• Repeat for opposite side installing gauge wheel in

same adjustment hole.

SHOULDER

BOLT

17/32 WASHER

GAUGE

WHEEL

MOUNTING

BRACKET

3/8-16

LOCKNUT

3/8 WASHER

GAUGE WHEEL

FIG. 7

INSTALL MULCHER PLATE (See Figs. 8A & 8B)

• Install two latch hooks to mulcher plate using screw,

washer, lock washer, and weld nut as shown.

NOTE: Pre-assemble weld nut to latch hook by inserting

weld nut from the top with hook pointing down.

• Tighten hardware securely.

• Raise and hold deflector shield in upright position.

• Place front of mulcher plate over front of mower deck

opening and slide into place, as shown.

• Hook front latch into hole on front of mower deck.

• Hook rear latch into hole on back of mower deck.

LOCK

WASHER

SCREW

WELD

NUT

LATCH

HOOK

SCREW

WASHER

LOCK

WASHER

WELD

NUT

LATCH

HOOK

WELD NUT

FROM THE TOP

HOOK POINTS

DOWN

WASHER

MULCHER

PLATE

FIG. 8A

FIG. 8B

DEFLECTOR

SHIELD

LATCH

HOOKS

✓

CHECKLIST

BEFORE YOU OPERATE AND ENJOY YOUR NEW

TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE

THE BEST PERFORMANCE AND SATISFACTION FROM

THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

✓ All assembly instructions have been completed.

✓ No remaining loose parts in carton.

✓ Battery is properly prepared and charged. (Minimum

1 hour at 6 amps).

✓ Seat is adjusted comfortably and tightened securely.

✓ All tires are properly inflated. (For shipping purposes,

the tires were overinflated at the factory).

✓ Be sure mower deck is properly leveled side-to-side/

front-to-rear for best cutting results. (Tires must be

properly inflated for leveling).

✓ Check mower and drive belts. Be sure they are routed

properly around pulleys and inside all belt keepers.

✓ Check wiring. See that all connections are still secure

and wires are properly clamped.

✓ Before driving tractor, be sure freewheel control is in

drive position.

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY

EXTRA ATTENTION TO THE FOLLOWING IMPORTANT

ITEMS:

✓ Engine oil is at proper level.

✓ Fuel tank is filled with fresh, clean, regular unleaded

gasoline.

✓ Become familiar with all controls - their location and

function. Operate them before you start the engine.

✓ Be sure brake system is in safe operating condition.

✓ It is important to purge the transmission before operat-

ing your tractor for the first time. Follow proper starting

and transmission purging instructions (See “TO START

ENGINE” and “PURGE TRANSMISSION” in Opera-

tion section of this manual).

CAUTION: Do not remove discharge

guard from mower. Raise and hold

guard when attaching mulcher plate

and allow it to rest on plate while in

operation.

TO CONVERT TO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store in a safe place.

Your mower is now ready for discharging or installation of

optional grass catcher accessory.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 50 51

Comments to this Manuals

No comments

Husqvarna LTH140 User Manual Page 9

Comments to this Manuals

Related products and manuals for Lawnmowers Husqvarna LTH140