EEEEnnnngggglllliiiisssshhhh 326HD A55 X-series 326HE3 X-series 326HE4 Oper ator ′ s manual Please r ead the operator’s manual carefully and make
10 – EnglishASSEMBLYFitting the hand guard and loop handle(326HDA55/326HE3)1 Assemble the hand guard and loop handle by screwing them together. Take c
English – 11ASSEMBLYFitting the impact guard(326HE4)Fit the guard using the three screws and washers. Fit the two short screws in hole A. Tighten the
12 – EnglishFUEL HANDLINGFuel safetyNever start the machine:1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporat
English – 13FUEL HANDLINGMixing• Always mix the petrol and oil in a clean container intended for fuel.• Always start by filling half the amount of the
14 – EnglishSTARTING AND STOPPINGCheck before starting• Inspect the working area. Remove any objects that could be thrown out.• Check the cutting atta
English – 15WORKING TECHNIQUESGeneral working instructionsPersonal protection• Always wear boots and other equipment described under the heading Perso
16 – EnglishWORKING TECHNIQUESSafety instructions after completing work• The transport guard should always be fitted to the cutting attachment when the
English – 17WORKING TECHNIQUES• Tighten the knob.Transport position(326HE4)Once the work has been completed fold the cutting unit back against the sha
18 – EnglishMAINTENANCECarburettorYour Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the
English – 19MAINTENANCEFine adjustment of the idle speed TAdjust the idle speed with the idle adjustment screw T, if adjustment is necessary. First tu
2 – English KEY T O SYMBOLS Symbols W ARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause seriou
20 – EnglishMAINTENANCECooling systemTo keep the working temperature as low as possible the machine is equipped with a cooling system.The cooling syst
English – 21MAINTENANCEGear housingThere is a grease nipple and a plug for filling lubricant on the gear housing. Use a grease gun to fill with grease.
22 – EnglishMAINTENANCE´®z+R#^¶6=¨´®z+R#^¶6=¨Maintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Mos
English – 23TECHNICAL DATATechnical dataNote 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/
´®z+R#^¶6=¨2005-09-23´®z+R#^¶6=¨1150036-26
English – 3 CONTENTS Contents Note the f ollowing before starting: Please read the oper ator’s manual carefully.Long-term exposure to noise can res
4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates
English – 5 WHA T IS WHA T? What is what?326HDA55326HE4 1 Cutter2 Grease nipple and plug for filling lubricant.3 Bevel gear4 Blade guard (326HDA55)
6 – English GENERAL SAFETY PRECA UTIONS Impor tantPersonal protective equipment HEARING PR OTECTIONWear hearing protection that provides adequate n
English – 7 GENERAL SAFETY PRECA UTIONS Mac hine ′′′′ s safety equipment This section descr ibes the machine ′ s safety equipment, its purpose, an
8 – EnglishGENERAL SAFETY PRECAUTIONSVibration damping systemYour machine is equipped with a vibration damping system that is designed to minimize vib
English – 9GENERAL SAFETY PRECAUTIONSBladesTo ensure good cutting results it is important that the contact pressure between the blades is correct. The
Comments to this Manuals