Husqvarna 650RTT User Manual

650RTTOwner's Manual / 96093000203 / 2008-09

10OPERATION• Soil conditions are important for proper tilling. Tines will not readily penetrate dry, hard soil which may con trib ute to excessive bo

11MAINTENANCEGENERAL RECOMMENDATIONSThe warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To re

12MAINTENANCEOIL FILLERPLUGOIL LEVELOIL DRAINPLUGFIG. 16Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment)

13AIR CLEANER CARTRIDGECOVERAIR CLEANER SCREWFIG. 18COOLING SYSTEM (See Fig. 19) Your engine is air cooled. For proper engine performance and long li

14SERVICE AND ADJUSTMENTSCAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug.TILLERTO ADJ

15SERVICE AND ADJUSTMENTSCABLE CLIPSCREWDRIVECONTROLCABLEEXTENSIONSPRINGENGINEPULLEYIDLERPULLEYTRANS MIS SION PULLEYLESS TEN SION5/8"MORETEN SIO

16tine_13tine_3SERVICE AND ADJUSTMENTSFIG. 26TINE REPLACEMENT (See Figs. 24, 25, and 26)CAUTION: Tines are sharp. Wear gloves or other prote

17SERVICE AND ADJUSTMENTSFIG. 27engine_art_78THROTTLE CONTROLCLAMP SCREWCASING AND WIREENGINETO ADJUST THROTTLE CONTROL CABLE (See Fig. 27)The thrott

18Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never store the t

19 Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engi

2• Keep children and pets away.• Do not overload the machine capacity by attempting to till too deep at too fast a rate.• Never operate the machin

20REPAIR PARTSTILLER - - MODEL NUMBER 650RTT (96093000203), PRODUCT NUMBER 960 93 00-02HANDLE ASSEMBLYKEY PART NO. NO. DESCRIPTION21 532 18 11-27 H

21KEY PART NO. NO. DESCRIPTION3 873 22 06-00 Nut, Hex 3/8-164 532 17 01-27 Shield, Inner Belt Guard RT5 532 16 43-29 Pin Spirol Flared6 532 1

22KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONREPAIR PARTSTILLER - - MODEL NUMBER 650RTT (96093000203), PRODUCT NUMBER 960 93 00-02MAINF

23KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm1 532 18 85-54 Transmission Assembly (In clu

2423 532 00 44-40 Hinge24 872 14 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr. 525 532 12 47-17 Cap, Vinyl26 532 10 92-27 Pad, Idler27 532 12 50-16

25KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTION1 532 00 44-59 Tine, Outer, L.H.2 532 13 26-73 Clevis Pin3 532 00 65-54 Tine, Inner,

261 532 42 20-12 Decal, Belt Guard2 532 41 83-98 Decal, Husqvarna, Control Panel3 532 42 33-64 Decal, Control Tine4 532 41 84-73 Decal, Tine S

27SERVICE NOTES

532 42 30-27 09.25.08 CLPrinted in U.S.A.

3CONGRATULATIONS on your purchase of a new tiller. It has been designed, en gi neered and manu fac tured to give you the best pos sible de penda bil i

4TOOLS REQUIRED FOR ASSEMBLYA socket wrench set will make assembly easier. Standard wrench sizes are listed.(1) Utility knife(1) Tire pressure gauge(

5carton_3handles_10ASSEMBLY• Grasp handle assembly. Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly in

6ASSEMBLYSHIFTRODHAIRPINCLIPSHIFTLEVERINDICATORREMOVE TILLER FROM CRATE• Make sure shift lever indicator is in “N” position (See Fig. 7)• Tilt tille

7KNOW YOUR TILLERREAD THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER.Compare the illustrations with your tiller to familiarize

8TURNING• Release the drive control bar.• Move throttle control to “SLOW” position.• Place shift lever indicator in “F” (forward) position. Tines

9OPERATIONengine_art_4OIL LEVELOIL DRAINPLUGOIL FILLERPLUGFIG. 12BEFORE STARTING ENGINEIMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENG