Husqvarna Cut-n-Break K 760 User Manual

EEEEnnnngggglllliiiisssshhhhK 760Operator’s manualPlease read the operator’s manual carefully and make sure you understand the instructions before usi

10 – EnglishASSEMBLING AND ADJUSTMENTSGeneralChecking the drive shaft and flange washersWhen the blade is replaced with a new one, check the flange wash

English – 11FUEL HANDLINGGeneralFuelGasoline• Use good quality unleaded gasoline.• The lowest recommended octane grade is 87 ((RON+MON)/2). If you run

12 – EnglishFUEL HANDLINGFuelingNever start the machine:• If you have spilled fuel or chain oil on the machine. Wipe off the spillage and allow remain

English – 13OPERATINGProtective equipmentGeneral• Do not use the machine unless you are able to call for help in the event of an accident.Personal pro

14 – EnglishOPERATINGWork area safety• Observe your surroundings to ensure that nothing can affect your control of the machine.• Ensure that no one/no

English – 15OPERATINGKickbackKickback is the sudden upward motion that can occur if the blade is pinched or stalled in the kickback zone. Most kickbac

16 – EnglishSTARTING AND STOPPINGBefore starting• Perform daily maintenance. See instructions in the section "Maintenance".Starting• Decompr

English – 17STARTING AND STOPPING• With a cold engine: The machine stops when the engine fires becase the chokel control is pulled out.Press the choke

18 – EnglishMAINTENANCEGeneral• Let your Husqvarna dealer regularly check the machine and make essential adjustments and repairs.Maintenance scheduleI

English – 19MAINTENANCECleaningExternal cleaning• Clean the machine daily by rinsing it with clean water after the work is finished.Cooling air intake•

2 – EnglishKEY TO SYMBOLSSymbols on the machine:WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause seriou

20 – EnglishMAINTENANCEReplacing the drive belt• First release the two bolts and then the adjuster screw to release the belt tension.• Now unscrew the

English – 21MAINTENANCEStarterChanging a broken or worn starter cord• Loosen the screws that hold the starter against the crankcase and remove the sta

22 – EnglishMAINTENANCEFitting the starter• To fit the starter, first pull out the starter cord and place the starter in position against the crankcase.

English – 23TECHNICAL DATATechnical dataCutting equipmentMotor K760Cylinder displacement, cm3/in374/4,5Cylinder bore, mm/inch 51/2Stroke, mm/inch 36/1

24 – EnglishFEDERAL EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme

´®z+UC[¶5h¨´®z+UC[¶5h¨

´®z+UC[¶5h¨2009-12-29´®z+UC[¶5h¨1153355-95!WARNING! Cutting, especially when DRY cutting, generates dust that comes from the material being cut, which

English – 3CONTENTSContentsKEY TO SYMBOLSSymbols on the machine: ... 2Explanation of warning levels ...

4 – EnglishPRESENTATIONDear customer!Thank you for choosing a Husqvarna product!It is our wish that you will be satisfied with your product and that it

English – 5PRESENTATIONWhat is what on the power cutter - K 760?1 Front handle2 Water tap3 Warning decal4 Air filter cover5 Cylinder cover6 Choke7 Thro

6 – EnglishMACHINE´S SAFETY EQUIPMENTGeneralThis section describes the machine′s safety equipment, its purpose, and how checks and maintenance should

English – 7MACHINE´S SAFETY EQUIPMENTVibration damping system• Your machine is equipped with a vibration damping system that is designed to reduce vib

8 – EnglishCUTTING BLADESGeneral• Cutting blades are available in two basic designs; abrasive baldes and diamond blades.• High-quality blades are ofte

English – 9CUTTING BLADESAbrasive blades for different materialsDiamond bladesGeneral• Diamond blades consist of a steel core provided with segments t