Husqvarna 345FX User Manual

EEEEnnnngggglllliiiisssshhhh 343F 345FX 345FXT 343FR 343R 345RX Oper ator’s manual (EPA) Please r ead the operator’s manual carefully and make

10 – EnglishGENERAL SAFETY PRECAUTIONSCutting attachment guardThis guard is intended to prevent loose objects from being thrown towards the operator.

English – 11GENERAL SAFETY PRECAUTIONSFor mufflers it is very important that you follow the instructions on checking, maintaining and servicing your ma

12 – EnglishGENERAL SAFETY PRECAUTIONSCutting equipmentThis section describes how to choose and maintain your cutting equipment in order to:• Reduce t

English – 13GENERAL SAFETY PRECAUTIONSSharpening the saw blade• See the cutting attachment packaging for correct sharpening instructions.A correctly s

14 – EnglishASSEMBLYAssembling the handlebar and throttleCAUTION! Some models have the throttle handle fitted at the factory.• Remove the screw at the

English – 15ASSEMBLYAssembling the cutting equipmentFitting the blade guard/combination guard, grass blade and ball-bearing-mounted support cup• Hang

16 – EnglishASSEMBLYFitting the blade guard and saw bladeCAUTION! Always use the recommended guard for the cutting attachment you are using. See chapt

English – 17ASSEMBLY• Tighten the trimmer head to a torque of 35-50 Nm (3.5-5 kpm).• To dismantle, follow the instructions in the reverse order.Fittin

18 – EnglishASSEMBLYTriobalance harnessSafety releasePush down the red release lever to release the machine from the harness.Adjusting the harness1 Ti

English – 19FUEL HANDLINGFuel safetyNever start the machine:1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evapor

2 – English KEY T O SYMBOLS Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in s

20 – EnglishFUEL HANDLINGMixing• Always mix the gasoline and oil in a clean container intended for fuel.• Always start by filling half the amount of th

English – 21STARTING AND STOPPINGCheck before starting• Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the cent

22 – EnglishSTARTING AND STOPPINGPART THROTTLE FUNCTION (RX):It is possible to set the engine for part throttle operation using the dial on the side o

English – 23WORKING TECHNIQUESGeneral working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot

24 – EnglishWORKING TECHNIQUESWorking methods• Before you start clearing, check the clearing area, the type of terrain, the slope of the ground, wheth

English – 25WORKING TECHNIQUES• To fell a tree forwards, the bottom of the tree should be pulled backwards. Pull the blade backwards with a quick, firm

26 – EnglishWORKING TECHNIQUESGrass trimming with a trimmer headTrimming• Hold the trimmer head just above the ground at an angle. It is the end of th

English – 27MAINTENANCECarburetorYour Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the e

28 – EnglishMAINTENANCEFine adjustment of the idle speed TAdjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. Fir

English – 29MAINTENANCE4 If the start throttle speed is too high, turn the adjuster screw A anticlockwise until the cutting attachment stops. Then tur

English – 3 CONTENTS Contents Note the f ollowing before starting: • Please read the operator’s manual carefully.Maintenance, replacement, or repai

30 – EnglishMAINTENANCEAn oiled foam plastic filter (available as an accessory) must be used if the machine is operated in extremely dusty conditions.

English – 31MAINTENANCETemperature 0°°°°C (32°°°°F) or colder:The air filter holder is prepared so it can be changed for use in the cold. Remove the ai

32 – EnglishMAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

English – 33TECHNICAL DATATechnical dataNote 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure lev

34 – EnglishTECHNICAL DATANote 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under vari

English – 35TECHNICAL DATANote 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under vari

36 – EnglishTECHNICAL DATA343RApproved accessories Type Cutting attachment guard, Art. no.Centre hole in blades/cutters, Ø 25,4 mm Output shaft thread

English – 37TECHNICAL DATA343F, 345FX, 345FXTApproved accessories Type Cutting attachment guard, Art. no.Centre hole in blades/cutters, Ø 20 mm Output

38 – EnglishFEDERAL EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme

4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates b

12345678935-50 NM~ 15 cm6'"Clic"~ 3,5 m11 '7,0 m23'2,4-3,3 mm.095"-.130"12 cm5"Trimmy SII

´®z+R;e¶5p¨´®z+R;e¶5p¨2,7-3,3 mm.106-.130"15 cm 6"15 cm 6"15 cm 6"15 cm 6"12356710111.)2.)>1,1 Kw<1,1 K

"Clic"123567910 m32'484,3 m14'2,7-3,3 mm.106-.13"10 cm 4"6"15 cmT45, T45x

´®z+R;e¶5p¨2007-03-23´®z+R;e¶5p¨1150276-95

English – 5 WHA T IS WHA T? What is what on the c learing saw? (343R, 345RX)26272830256325 1713111012142316154222434932873318201921413121293535 1

6 – English WHA T IS WHA T? What is what on the c learing saw? (343F, 345FX, 345FXT)242725262363251311101298717291416152122181420181928 1 Saw blad

English – 7 WHA T IS WHA T? What is what on the c learing saw? (343FR)262728303242531349338724212320412029222214201921632513111012171416151819 1 B

8 – English GENERAL SAFETY PRECA UTIONS Impor tantPersonal protective equipment HELMET A helmet should be w orn if the trees being cleared are tall

English – 9 GENERAL SAFETY PRECA UTIONS Mac hine ′′′′ s safety equipment This section descr ibes the machine ′ s safety equipment, its purpose, an