Husqvarna K1250 User Manual

EEEEnnnngggglllliiiisssshhhh K1250 Oper ator’s manual (EPA) Please r ead the operator’s manual carefully and make sure you understand the instructio

10 – EnglishSAFETY INSTRUCTIONSCuttingGeneral• Start cutting with the machine running at maximum speed.• Always hold the machine in a firm grip with bo

English – 11SAFETY INSTRUCTIONSHow to avoid kickbackWhat is kickback?The word kickback is used to describe the sudden reaction that causes the power c

12 – EnglishSAFETY INSTRUCTIONSHigh speed handheld machinesOur cutting blades are manufactured for high-speed, portable power cutters. If blades from

English – 13ASSEMBLYAssembling the cutting headRemove the bolt (1) and nut (2). Remove the guard. Fit the drive belt on the clutch drum. Fit the guard

14 – EnglishFUEL HANDLINGFuelCAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-st

English – 15STARTING AND STOPPINGStarting and stoppingStarting a cold engineIgnition: Slide the ignition switch to the left.Choke: Pull the choke cont

16 – EnglishMAINTENANCETensioning the drive belt• The drive belt is fully enclosed and well protected from dust and dirt.• When tensioning the drive b

English – 17MAINTENANCEFine adjustment of the idle speed TAdjust the idle speed using the T screw. When an adjustment is necessary, first turn the scre

18 – EnglishMAINTENANCEStarterChanging a broken or worn starter cord• Loosen the screws that hold the starter against the crankcase and remove the sta

English – 19MAINTENANCESpark plugThe spark plug condition is influenced by:• Incorrect carburetor adjustment.• Wrong fuel mixture (too much oil).• A di

2 – English KEY T O SYMBOLS K ey to symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serio

20 – EnglishMAINTENANCEGeneral maintenance instructionsBelow you will find some general maintenance instructions. If you have more questions, contact y

English – 21TECHNICAL DATACutting equipmentEngine K1250Cylinder displacement, cu.in/cm37,25/119Cylinder bore, inch/mm 2,36/60Stroke, inch/mm 1,65/42Id

22 – EnglishFEDERAL EMISSION CONTROL WARRANTY STATEMENT´®z+R==¶5X¨´®z+R==¶5X¨YOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protect

´®z+R==¶5X¨2007-01-02´®z+R==¶5X¨1150292-95!WARNING! Cutting, especially when DRY cutting, generates dust that comes from the material being cut, which

English – 3 CONTENTS Contents KEY TO SYMBOLS K ey to symbols ... 2 CONTENTS Contents ..

4 – English WHA T IS WHA T? What is what on the po wer cutter?1713129108111815222191415673162021423 1 Cylinder cover2 Muffler3 Fuel tank4 Start thr

English – 5 SAFETY INSTRUCTIONS Steps before using a new power cutter • Please read the operator’s manual carefully.• Check the cutting blade’s moun

6 – English SAFETY INSTR UCTIONS • Heavy-duty, firm grip gloves.• Tight-fitting, heavy-duty and comfortable clothing that permits full freedom of mov

English – 7 SAFETY INSTR UCTIONS Thr ottle lockout The throttle tr igger lock is designed to prevent accidental operation of the throttle. When the

8 – EnglishSAFETY INSTRUCTIONSThrottle lockout• Make sure the throttle control is locked at the idle setting when the throttle lockout is released.• P

English – 9SAFETY INSTRUCTIONSFuel safety(Refuelling/Fuel mixture/Storage.)• Never refuel the machine while the engine is running.• Make sure there is