Operator ManualRZ3019BF / 966582101Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
10Operate machine only in daylight or good articial • light.Do not operate the machine while under the • inuence of alcohol or drugs.Watch for
11Personal Safety EquipmentMake sure that you have rst aid equipment close • at hand when using the machine.Never use the machine when barefoot
128011-517Never allow children to operate the machine8011-518Keep children away from work areaChildrenTragic accidents can occur if the operator
138011-516Never fill the fuel tank indoorsSafe Handling of GasolineTo avoid personal injury or property damage, use extreme care in handling gaso
148011-515Never drive the machine in an enclosed spaceGeneral MaintenanceNever operate machine in a closed area.• Keep all nuts and bolts tight
15Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, re or eye inj
16IMPORTANT INFORMATIONThe parking brake is not sufcient to lock the machine in place during transport. Ensure that the machine is well fastene
17SLOWCHOKEFASTTHROTTLEThis operator’s manual describes the Husqvarna Zero Turn Rider. The rider is tted with a Briggs & Stratton four-st
188050-003Steering controlsSteering Control LeversThe machine’s speed and direction are continuously variable using the two steering controls.
19SLOWCHOKEFASTTHROTTLESLOWCHOKEFASTTHROTTLEThrottle ControlThe throttle control regulates the engine speed and thereby the rate of rotation o
©2010 HTC All rights reserved.Beatrice, NE. Printed in U.S.A.In order to implement improvements, specications and designs can be altered without prio
20SLOWCHOKEFASTTHROTTLEChoke ControlThe choke control is used for cold starts in order to provide the engine with a richer fuel mixture.For co
21Fuel Shut Off ValveThe fuel shut off valve is located in the fuel line under the seat. Tilt seat forward for access. The fuel valve is ON wh
22Manual TransportWhen pushing or pulling the mower, be sure to engage the EZT Hydrogear bypass linkages. The EZT bypass linkages are located
23Read the Safety section and following pages, if you are unfamiliar with the machine.TrainingZero turn mowers are far more maneuverable than
24Before StartingRead the sections Safety Instructions and • Controls before starting the machine.Perform the daily maintenance before starti
25SLOWCHOKEFASTTHROTTLESLOWCHOKEFASTTHROTTLEMove the steering controls outward to the locked (outer) neutral position.Move the throttle to th
268050-135Turn to START position8050-136Release ignition to the RUN position8050-010Open the fuel valveOpen the fuel valve.Press in and turn
27SLOWCHOKEFASTTHROTTLESlowly push the choke control down when the engine has started.Set the desired engine speed with the throttle. Allow t
28RunningRelease the parking brake by moving the lever 1. downward. NOTE: The mower is equipped with an operator presence system. When the en
29Operating on HillsRead the Safety Instructions Driving on Slopes in the Safety Instructions.The slowest speed possible should be used • bef
30Mowing TipsObserve and ag rocks and other xed objects to • avoid collisions.Begin with a high cutting height and reduce it until • the de
31Stopping the EngineAllow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has been wor
32Manual TransportWhen pushing or pulling the mower, be sure to engage the EZT Hydrogear bypass linkages. The EZT bypass linkages are located
33Maintenance ScheduleThe following is a list of maintenance procedures that must be performed on the machine. For those points not describ
341) First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours.2) In dusty
35BatteryYour mower is equipped with a maintenance free battery that does not need servicing. However, periodic charging of the battery wit
36Safety SystemThe machine is equipped with a safety system that prevents starting or driving under the following conditions.The engine can
37Parking BrakeVisually check that no damage is found on the lever, links, or switch belonging to the parking brake. Perform a standstill t
38321WARNING!The engine and the exhaust system, become very hot during operation. Risk for burns if touched. Allow engine and exhaust syste
39Adjusting the Mower DeckWARNING!Before performing any service or adjustment checklist:1. Engage the parking brake.2. Place the Blade
WARNING!Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these
40123Caster WheelsCheck every 200 hours. Check that wheels rotate freely. If wheels do not rotate freely take the unit to your dealer for s
41GeneralRemove the ignition key to prevent unintentional movements during lubrication.When lubricating with an oil can, it must be lled w
42Front Wheel MountLubricate with a grease gun, one zerk for each wheel mount, until the grease is forced out.Use only good quality bearing
43Problem CauseThe engine will not start. Blade lever is engaged.• Steering controls are not locked in neutral • position.Driver is n
44Problem CauseThe engine seems weak. Clogged air lter.• Fouled spark plugs.• Carburetor incorrectly adjusted.• The engine overheats
45Winter StorageAt the end of the mowing season, the machine should be readied for storage (or if it will not be in use for longer than 30 days
46 8053-002
47HEX HEAD CAP SCREWSThe torque values shown should be used as a general guideline when specic torque values are not given.U.S. Standar
481) Refer to the engine manufacturer's Owner's Manual for engine specications.2) The power rating of the engines indicate
49RZ3019 BF / 966582101EquipmentCutting width 30"Cutting height 1½" - 4” / 2.5 cm - 10.6 cmNumber of blades 1Blade length 15&
5CongratulationsThank you for purchasing a Husqvarna ride-on mower. This machine is built for superior efciency to rapidly mow primarily
50USA RequirementsLabels are placed on the engine and/or in the engine compartment stating that the machine will fulll the req
51Delivery ServiceCharge the battery.qAdjust the tire pressure of all wheels to 15 PSI (1 bar).qMou
5225-Hour ServiceCheck the fuel pump’s air lter.qSharpen/Repla
53 100-Hour ServicePerform the 25-hour service.qPerform the 50-
54At Least Once Each YearClean the engine’s cooling air intake
P/N 115 355026R1 03/08/10
6Good ServiceHusqvarna’s products are sold only in specialized retail stores with complete service. This ensures that you as a customer re
7R NThese symbols are found on the machine and in the operator’s manual.Study them carefully so that you know what they mean.IMPORTA
8 Read Shut off engine and Keep a safe Use on slopes No passengers Operator’s remove key before distance from no greater
9Safety InstructionsThese instructions are for your safety. Read them carefully.General OperationRead, understand, and follow all instructions o
Comments to this Manuals