Husqvarna 14 Pro User Manual

101 90 55-26Rider 14 ProOperator´s manualPlease read these instructions carefully and make sureyou understand them before using the machine.

8 – EnglishThrottle controlThe throttle control regulates the engine speed, andthereby also the rotation speed of the blades.To increase or reduce the

English – 9Cutting unitRider 14 Pro can be equipped with numerousattachments.The BioClip unit finely cuts the lawn by cutting thegrass several times b

10 – EnglishPRESENTATION!WARNING!Petrol is highly inflammable. Exercisecare and refuel outdoors (see safetyinstructions).FuellingThe engine should be

English – 11Before starting• Read the safety instructions and information onthe location and function of the controls beforestarting (see pages 5–12).

12 – English5. When the engine starts release the ignition keyimmediately back to neutral position.IMPORTANT INFORMATIONDo not run the starter for mor

English – 133. Push in the lock button on the lift lever and lowerdown the cutting unit.DRIVING4. Select the required cutting height (1–9) with thecut

14 – EnglishStopping the enginePreferably allow the engine to idle for a minute toobtain normal working temperature before stoppingit if it has been w

English – 15Maintenance scheduleThe following is a list of the maintenance which should be conducted on the machine. For the items whichare not descri

16 – EnglishRemoving of the machine hoodsEngine hoodRelease the two rubber straps on the rear edge ofthe engine hood and lift off the hood.MAINTENANCE

English – 17MAINTENANCEChecking of the fuel pump’s air filterCheck regularly that the fuel pump’s air filter is freefrom dirt.The filter can when nece

Svenska – 31Sve-5 225/232/235 Bruk 97-11-25, 08.4631

18 – EnglishCheck the transmission’s air intakeCheck that the transmission’s air intake in notblocked.Check the transmission’s oil level1. Check the t

English – 19Checking and adjustment of thesteering wiresThe steering is controlled by means of wires.These can in time become slack, which implies tha

20 – EnglishAdjusting the brakesThe brakes are adjusted as follows:1. Loosen the lock nuts (1).2. Adjust the wire using the adjuster screw (2) untilth

English – 21Replacing the air filterIf the engine seems to lack power or does not runsmoothly this may be because the air filter isclogged.It is there

22 – EnglishMAINTENANCE123Fitting the cutting unit1. Position the Rider on a flat surface and applythe parking brake, see page 10. Check that thelever

English – 23MAINTENANCEBioClip 10312892. Adjust the unit’s ground pressure by screwing inor out the adjusting screws located behind thefront wheels on

24 – EnglishMAINTENANCEChecking the cutting unit’s parallelismCheck the parallelism of the cutting unit as follows:1. Place the machine on a level sur

English – 25MAINTENANCERemoving the cutting unit1. Apply the parking brake, see page 10.2. Adjust the cutting height to its lowest setting.3. Remove t

26 – English8. Place one foot on the front edge of the cuttingunit. Raise the front edge of the unit slightly andunhook the height adjustment strut.9.

English – 27MAINTENANCEReplacing the cutting unit’s beltsBelt replacement on the BioClip 103Two transmission belts that synchronise the rota-tion of t

English – 1Operator’s Manual forRider 14 ProCONTENTSIMPORTANT INFORMATIONRead through these instructions carefully so that you know how to use and mai

28 – EnglishMAINTENANCEIMPORTANT INFORMATIONThe blades on a BioClip unit should beset at 90 degrees to each other. In allother cases the blades can co

English – 29MAINTENANCEService position for cutting unitThe cutting head can be placed in the serviceposition to provide easy access for cleaning, rep

30 – EnglishMAINTENANCE4. Fit the support wheels on either side of the rearof the cutting unit.5. Disengage the spring from the drive belttensioning w

English – 31MAINTENANCERestoring from service positionTo restore the machine from the service position,reverse the sequence “Placing in Service positi

32 – EnglishMAINTENANCEChecking the bladesTo achieve the best mowing results it is importantthat the blades are undamaged and well-sharpened.Check tha

English – 33MAINTENANCEChanging the oilThe oil should be changed for the first time after 8hours of running time. Thereafter it should bechanged every

34 – EnglishMAINTENANCEIMPORTANT INFORMATIONCheck that the lock-ring is correctly posi-tioned in the slot.Lubrication of front wheel bearings1. Remove

English – 35Checking and adjustment of the throttlewireCheck that the engine responds to the throttlecontrol and that the correct engine speed isachie

36 – EnglishMAINTENANCEReplacement of the fuel filterReplace the fuel filter every 100 running hours(once per season) or more frequently if it isclogg

English – 37TROUBLE SHOOTING SCHEDULEProblem ProcedureEngine will not start. • Fuel tank empty.• Plugs defective.• Plug connections defective.• Dirt i

2 – EnglishThese symbols are on the machine and in the instructions.Study them carefully so that you know what they mean.Read the instructions.Reverse

38 – EnglishWinter storageSTORAGETo put the machine in order for storage follow theseinstructions:1. Carefully clean the machine, especially underthe

English – 39WIRING DIAGRAM1. Brake switch, hydrostat2. Microswitch, cutting unit3. Microswitch, seat4. Ignition lock5. Counter6. Start relay7.

40 – EnglishTECHNICAL DATAWhen the service life of this product has been served and it is no longer used it should bereturned to the dealer or to an a

English – 41Cutting unitTECHNICAL DATABioClip 90 BioClip 103Cutting width 900 mm 1030 mmCutting heights 9 settings, 45-95 mm 9 settings, 45-95 mmBlade

´*3%T¶6q¨2000W02

English – 3These instructions are for your safety. Read them carefully.SAFETY INSTRUCTIONSThis symbol implies that important safety rules are applicab

4 – English• Watch out for traffic when working close to aroad, or crossing one.• Be careful when rounding a fixed object so thatthe blades do not hit

English – 5• Do not cut close to edges, ditches or banks. Themachine can suddenly tip over if a wheel goesover the edge of a drop or a ditch, or if a

6 – English• Check the fuel level each time before using themachine, and leave space for the fuel to expandsince the heat from the engine and hot sun

English – 7PresentationCongratulations on choosing an excellent qualityproduct, Rider ProFlex. These instructions describethe Rider 14 Pro.The Rider 1