1330SBEXPOwner's Manual
10TO THROW SNOW (See Fig. 15)The auger rotation is controlled by the auger control lever located on the right side handle.• Squeeze auger control
11SPEED and DIRECTION are controlled by the drive speed control lever.• Press downward on the speed control lever and move lever to de sired po s
12NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be
13damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied be fore stor age of 30 days or lo
14• After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.• Clean the entire snow th
15MAINTENANCESNOW THROWERAlways observe safety rules when performing main te nance.TIRES• Maintain proper air pressure in both tires (14–17 P.S.I
16SERVICE AND ADJUSTMENTSWARNING: To avoid serious injury, before performing any service or ad- just ments:1. Be sure throttle is in STOP position.2.
17SERVICE AND ADJUSTMENTSTO REPLACE BELTS (See Fig. 24)The auger and traction drive belts are not adjustable. If the belts are damaged or begin to sli
18STORAGEImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never
19Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position.
2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure
20REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLYSNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93
21KEY PART NO. NO. DESCRIPTION 1 532 18 86-63 Bar, Weight 2 532 75 11-53 Nut, Hex 5/16-18 3 872 11 05-10 Bolt, Carriage 5
22REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTESNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961
23REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTESNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961
24REPAIR PARTS HANDLESSNOW THROWER - MODEL NO. 1330SBEXP (961
25REPAIR PARTS HANDLESSNOW THROWER - MODEL NO. 1330SBEXP (961
26REPAIR PARTS DRIVESNOW THROWER - MODEL NO. 1330SBEXP
27REPAIR PARTS DRIVESNOW THROWER - MODEL NO. 1330SBEXP
28REPAIR PARTS CHASSIS / ENGINE / PULLEYSSNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODU
29REPAIR PARTS CHASSIS / ENGINE / PULLEYSSNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODU
3PRODUCT SPECIFICATIONSGasoline Capacity 4.0 Quartsand Type: Unleaded Regular onlyOil Type SAE 30 (above 40°F)(API SG–
30REPAIR PARTS WHEELS / DECALSSNOW THROWER - MODEL NO. 1330SBEXP (96193001900
31REPAIR PARTS WHEELS / DECALSSNOW THROWER - MODEL NO. 1330SBEXP (96193001900
532 40 57-43 Rev. 3 08.23.06 BY Printed in U.S.A.SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Hus
4PARTS PACKED SEPARATELY IN CARTON
5ASSEMBLY / PRE-OPERATIONRead these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Rea
6ASSEMBLY / PRE-OPERATIONAUGERCONTROL RODCONTROL ARMRUBBER SLEEVELOOP OPENING UPFIG. 5INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)The auger control r
7ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins
8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with
9MEETS A.N.S.I. SAFETY REQUIREMENTSOur snow throwers conform to the standards of the American National Standards Institute.FIG. 10OPERATIONDrive speed
Comments to this Manuals