EEEEnnnngggglllliiiisssshhhhK 3600 MKIIOperator′s manualPlease read the operator’s manual carefully and make sure you understand the instructions befo
10 – EnglishSAFETY INSTRUCTIONS• Be alert to movement of the work piece or anything else that can occur, which could cause the cut to close and pinch
English – 11SETTINGS AND ADJUSTMENTSDriveOn account of the machine’s unique design the driving power is not transferred at the centre of the blade. Th
12 – EnglishSETTINGS AND ADJUSTMENTS• Loosen the knob to offload the springs.• Pull out the lock for the front handle and move the handle to the servic
English – 13SETTINGS AND ADJUSTMENTSCAUTION! The machine should be upright. If the machine lies on its side the weight of the blade makes it difficult
14 – EnglishSTARTING AND STOPPINGStarting and stoppingStarting• Grip the front handle with the left hand.• Grip the rear handle with the right hand. W
English – 15MAINTENANCEMaintenanceDismantling the complete guide roller• Remove the support roller cover.• Lift off the blade.• Unscrew the knob. Firs
16 – EnglishMAINTENANCEDrive wheel1 Lock the axle using the locking button. See the instructions under the heading What is what?.2 Loosen the centre s
English – 17MAINTENANCEReconstructing the bladeCouplings1 Water2 Water filter3 Return4 PressureIMPORTANT! If the coupling is dirty, the dirt can enter
18 – EnglishMAINTENANCEMaintenance scheduleCAUTION! The chart is based on daily use of the equipment.Blades conforming to EN13236Husqvarna K3600 MKII
English – 19TROUBLE SHOOTINGMechanicsSymptom Probable causeThe blade does not rotate. Roller knobs not tightened fully.The blade not fitted on guide ro
2 – EnglishKEY TO SYMBOLSKey to symbols WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fat
20 – EnglishTECHNICAL DATA*We recommend the use of environmentally approved hydraulic oil.**With high ambient temperatures use oil with a higher visco
English – 21TECHNICAL DATAEC-declaration of conformityHusqvarna AB, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility
´®z+UBT¶6A¨´®z+UBT¶6A¨
´®z+UBT¶6A¨2010-01-13´®z+UBT¶6A¨1153345-26Original instructions
English – 3CONTENTSContentsKEY TO SYMBOLSKey to symbols ... 2CONTENTSContents ...
4 – EnglishWHAT IS WHAT?What is what on the power cutter?1 Diamond blade2 Blade guard/spray guard3 Hydraulic motor4 Locking button for the drive wheel
English – 5SAFETY INSTRUCTIONSSteps before using a new power cutter.• This machine is a hydraulically operated power cutter intended for free-hand cut
6 – EnglishSAFETY INSTRUCTIONSSwitch lock and ON/OFF valve for the waterThe switch lock is designed to prevent accidental operation of the switch. The
English – 7SAFETY INSTRUCTIONSChecking the blade guardCheck that the guard is complete and without any cracks or deformations.General safety precautio
8 – EnglishSAFETY INSTRUCTIONSCuttingGeneral• Start cutting with the machine running at maximum speed.• Always hold the machine in a firm grip with bot
English – 9SAFETY INSTRUCTIONSLarge workCuts exceeding 1 m - secure a batten along the line to be cut. The batten acts as a guide. Use this guide to m
Comments to this Manuals