Operators Manual111280 / HCS9111281 / HCS13Models:Please read these instructions carefully and makesure you understand them before using the machine.M
10ASSEMBLY9. With the hood open, secure the (3) bags inplace. The back of the bags will hook overthe mounting tabs on the hitch assembly.Figure 5.10.
11ASSEMBLYBlower/Drive Kit1. Open the drive kit box and remove all ofthe components.2. Place the deck in the lowest cuttingheight.3. Remove the right
12ASSEMBLY12. Re-install the pulley shield.13. Cut the blower housing along the dashedline to fit the 52" and 61" decks. Drill thetwo small
13ASSEMBLY18. Remove the discharge chute from the deck.19. Place the deck plate pin in the tube on theback edge of the deck. Rotate the bloweraround
14Operating the Collection System1. NEVER USE THE COLLECTION SYSTEMWITHOUT THE BLOWER ASSEMBLYAND HOSES SECURELY ATTACHED.2. Make sure hoses are conne
15 Preventative Maintenance Schedule Item Before Every
16Caring For Hoses1. Inspect hoses before each use. If hoses haveexcessive wear, tears, or punctures, replaceimmediately.2. To prolong the life of th
17 PROBLEM POSSIBLE CAUSE CORRECTION Loss of Vacuum. 1. Blower, hose or hood inlet clogge
18NOTE: Your Front Weight Bar may look different from those shown in this diagram.SPINDLE DRIVE ASSEMBLY
19PARTS ILLUSTRATIONS
2©2005 Husqvarna. All Rights Reserved.Beatrice, NE. Printed in U.S.A.
20HOOD ASSEMBLY123456789101112131415161718192210205231923232123201424
21ITEM PART NO. QTY DESCRIPTION1 ... 539111172 ...1...HOOD2 ... 539111174 ...1...HOOD SUPPORT3 ...
22HITCH ASSEMBLY123456789101112131415151718192016151115111511
23ITEM PART NO. QTY DESCRIPTION1 ... 539111155 ... 1...HITCH2 ... 539111190 ... 1...LATCH3 ...
24BLOWER ASSEMBLY12345678910111213141516171819202122232425262728293031323334353637383940413731537373737273340LOCKING COLLARTHIS SIDE UPTHIS SIDE DOWNH
25ITEM PART NO. QTY DESCRIPTION1 ... 539111225 ... 1...FLOOR WELDMENT2 ... 539111227 ... 1...BEARING
26WEIGHT KITITEM PART NO. QTY DESCRIPTION1 ... 539020255 ... 1...WEIGHT BAR, FRONT2 ... 539111313 ... 1...
27WEIGHT KITMODEL HCS9ITEM PART NO. QTY DESCRIPTION1 ... 539111313 ... 1...HOLD DOWN, WEIGHT BAR2 ... 539102049
28MOUNTING KITMODEL HCS1312345678910111213141516171819202191214REF.
29ITEM PART NO. QTY DESCRIPTION1 ... 539111322 ... 1...HITCH BRACKET, RIGHT, W/DECAL... 539111199 ...1...
3Operators GuideFeatures and Controls... 4General Information ...
30MOUNTING KITMODEL HCS9123456781112131415161718192021222314166REF.
31ITEM PART NO. QTY DESCRIPTION1 ... 539111294 ... 1...HITCH BRACKET W/DECALS, RIGHT... 539111203 ... 1...
32BAG ASSEMBLYITEM PART NO. QTY DESCRIPTION1 ... 539110063... 1...HANGER, BAG2 ... 539111166 ...1...T
33DRIVE KIT ASSEMBLYITEM PART NO. QTY DESCRIPTION1 ... 539109660 ... 1...DRAW LATCH2 ... 539110740... 2...
34DRIVE KIT ASSEMBLY(539) 111276 - 48 INCH DECKITEM PART NO. QTY DESCRIPTION1 ... 539109660 ... 1...DRAW LATCH2 ...
35DRIVE KIT ASSEMBLY(539) 111277 - 52 INCH DECKITEM PART NO. QTY DESCRIPTION1 ... 539109660 ... 1...DRAW LATCH2 ...
36DRIVE KIT ASSEMBLY(539) 111278 - 61 INCH DECKITEM PART NO. QTY DESCRIPTION1 ... 539109660 ... 1...DRAW LATCH2 ...
37
4NOTE: Your Front Weight Bar may look different from those shown in this diagram.FEATURES & CONTROLSBLOWER ASSEMBLYHOSEBAGREAR GUARDCAST WEIGHTW
5SAFETY RULESSafety Procedures1 - Training:• Read the Operator’s manual. If the operator(s)or mechanic(s) can not read English it is theowner’s respo
6SAFETY RULES3 - Operation• Never run an engine in an enclosed area.• Only operate in good light, keeping away fromholes and hidden hazards.• Slow dow
7ASSEMBLYUnpacking InstructionsAssembly InstructionsCollection SystemTools Required:RatchetTorque Wrench1/2" Wrench1/2" Socket9/16" Wre
8ASSEMBLY4. Remove the (10) 5/16 carriage bolts thatsecure the standard rear guard to the strapsand skid plates. Remove the standard rearguard. Repl
9ASSEMBLY7. Place the hood assembly on to the hitchassembly. Place both hood hinges betweenthe upper hitch mounts on the hitch assembly.Be sure that
Comments to this Manuals