GGGGBBBB EEEEnnnngggglllliiiisssshhhh K760K760 Rescue Operator ′ s manual Please read the operator’s manual carefully and make sure you understand
CUTTING BLADES 10 – English Abrasive blades • The cutting material on abrasive blades consists of grit bonded using an organic binder. ”Reinforced bl
CUTTING BLADESEnglish – 11Diamond blades and cooling• During cutting the friction in the cut causes the diamond blade to be heated up. If the blade is
ASSEMBLING AND ADJUSTMENTS12 – EnglishGeneralHusqvarna’s blades are high speed blades approved for hand held power cutters.Checking the drive shaft an
ASSEMBLING AND ADJUSTMENTSEnglish – 13Disengaging OilGuard (K760 OilGuard)• When the machine is delivered, the OilGuard plug (A) and the blue indicato
FUEL HANDLING14 – EnglishGeneralFuelPetrol• Use good quality unleaded or leaded petrol.• The lowest octane recommended is 90 (RON). If you run the eng
FUEL HANDLINGEnglish – 15FuelingNever start the machine:• If you have spilt fuel or engine oil on the machine. Wipe off the spill and allow the remain
OPERATING16 – EnglishProtective equipmentGeneral• Do not use the machine unless you are able to call for help in the event of an accident.Personal pro
OPERATINGEnglish – 17Work area safety• Observe your surroundings to ensure that nothing can affect your control of the machine.• Ensure that no one/no
OPERATING18 – English• Maintain a safe distance from the cutting blade when the engine is running.• Never leave the machine unsupervised with the moto
OPERATINGEnglish – 19Risk areaNo persons that do not have the protective equipment described above shall be allowed inside the risk area for thrown ma
KEY TO SYMBOLS 2 – English Manual version This manual is the International version used for all English speaking countries outside North America. If
OPERATING20 – EnglishKickback zoneNever use the kickback zone of the blade for cutting. If the blade is pinched or stalled in the kickback zone, the r
OPERATINGEnglish – 21How to aviod kickbackAvoiding kickback is simple.• The work piece must always be supported so that the cut stays open when cuttin
STARTING AND STOPPING22 – EnglishBefore starting• Perform daily maintenance. See instructions in the section "Maintenance".StartingWith a co
STARTING AND STOPPINGEnglish – 23With a warm engine:• Make sure that the stop switch (STOP) is in the left position.• Set the choke control in the cho
24 – EnglishMAINTENANCEGeneral• Let your Husqvarna dealer regularly check the machine and make essential adjustments and repairs.Maintenance scheduleI
MAINTENANCEEnglish – 25CleaningExternal cleaning• Clean the machine daily by rinsing it with clean water after the work is finished.Cooling air intake•
MAINTENANCE26 – EnglishReplacing the drive belt• First release the two bolts and then the adjuster screw to release the belt tension.• Now unscrew the
MAINTENANCEEnglish – 27StarterChanging a broken or worn starter cord• Loosen the screws that hold the starter against the crankcase and remove the sta
MAINTENANCE28 – EnglishChanging a broken recoil spring• Undo the bolt in the centre of the pulley and remove the pulley.• Bear in mind that the return
English – 29TECHNICAL DATATechnical dataNote 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/
CONTENTS English – 3 Contents KEY TO SYMBOLS Manual version ... 2Symbols on the machine ...
30 – EnglishTECHNICAL DATAEC-declaration of conformity(Applies to Europe only)Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares u
1155019-26´®z+W!|¶6-¨´®z+W!|¶6-¨2013-02-19GB - Original instructions
PRESENTATION 4 – English Dear Customer, Thank you for choosing a Husqvarna product!It is our wish that you will be satisfied with your product and tha
English – 5 PRESENTATION What is what on the power cutter - K760? 1 Front handle2 Water tap3 Warning decal4 Air filter cover5 Cylinder cover6 Choke co
6 – English PRESENTATION What is what on the power cutter - K760 Rescue? 1 Front handle2 Warning decal3 Air filter cover4 Cylinder cover5 Choke contro
MACHINE´S SAFETY EQUIPMENT English – 7 General This section describes the machine´s safety equipment, its purpose, and how checks and maintenance s
MACHINE´S SAFETY EQUIPMENT 8 – English Blade guard This guard is fitted above the cutting blade and is designed to prevent parts of the blade or cutti
CUTTING BLADES English – 9 General • Cutting blades are available in two basic designs; abrasive blades and diamond blades.• High-quality blades ar
Comments to this Manuals