Operator’s manual Bedienungsanweisung Manuel d’utilisation Manuai del operador101 86 32-31
0 Fuel and chain lubricationWARNING! The chain saw isequipped with a two-stroke engine. Always run the saw with fuel,which is mixed with oil.Provide f
Chain oil Kettenöl Huile à chaîne Aceite de cadenaé0 Chain oil• The chain lubrication system is automatic. Always use special chain oil with
©Start and stopWARNING!• Never startthe saw engine without the bar, chain and clutch cover (chain brake) assembled—or else the clutch can come loose
0 StartGrip the front handle with your left hand and hold the saw down by putting your right foot in the rear handle.Pull the starter handle with your
©©©Chain brakeThe saw is equipped with a chain brake. The brake is designed to stop the chain immediately in the event of a kick-back. T
©Control and maintenance of the chain brakeBraking function controi:The chain brake must be checked several times daily. Place the saw on firm gro
©CarburettorWARNING! Do not start the saw without the bar, chain and clutch cover assembled. If you do, the clutch might come loose and caus
VergaserACHTUNG! Die Säge darf erst dann gestartet werden, wenn Schiene, Kette und Kupplungsdeckei (Kettenbremse) montiert sind.Unter Ums
©CarburateurATTENTION! Guide-chaîne, chaîne et carter d’embrayage doivent être montés avant le démarrage de la tronçonneuse, sinon l’embraya
(EspiCarburadorADVERTENCIA! Antes de arrancar la sierra es necesario que estén montados la espada, la cadena y el envolvente del embr
©____________________Before using your new chain saw• Read the Operator’s Manual carefully.• Check the assembly and adjustment of the cutting equipm
©Starter deviceWARNING!• When the recoil spring is assembled in the starter housing, it is in tensioned position and can when treated carelessly, pop
0 Tensioning the recoil springLift the starter cord up in the notch on the starter pulley and turn the starter pulley 2 turns clockwise.NOTE! Check th
Air filterThe air filter must be regularly cleaned from dust and dirt in order to avoid:• Carburettor malfunctions • Starting problems • Engine power
©©©Spark plugThe spark plug condition is influenced by:• An incorrect carburettor setting.• Wrong fuel mixture (too much oil in the gasoline).• A d
MufflerThe muffler is designed in order to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot
0 Winter useDuring winter time, powder snow and cold weather can cause running problems, such as: • Too low engine temperature. • Icing on the air fii
©MaintenanceBelow you will find some general maintenance instructions. If you havemore questions, contact your servicing dealer.Daily maintenance:1. C
12 16,2023 10 13 24 21,2210 9©EntretienNous donnons ici quelques conseils de caractère général. Pour desquestions plus précises, contacter votre répa
©Chain maintenance — safetyFor the personal safety, it is of great importance, that the bar and chain combinations of so called low kick ty
0 SharpeningNever cut w/ith a dull saw chain. A chain which does not cut unless you press it hard against the wood is damaged, dull or incorrectly fil
The following text is required by the US authorities.(ANSI B 175.1—1985 Appendix D)Safety Precautions for Chain Saw UsersD1. Kickback Safety Precautio
WARNING! If a too small filing size is used or the file is kept too deep in the cutting tooth, the chain will be dangerously aggressive. This
0 Chain lubricationFill up the chain oil tank with chain oil each time you fuel. Never run the chain dry. Insufficient oil may cause friction which le
0 Equipment neededClothingThe proper clothing and equipment (as shown) protect you from many potential hazards such as lacerations, thrown
0 Tools and materialsThe tools and material shown are absolutely essential for routine everyday safe operation and maintenance of a chain
©GeneralAvoid cutting in adverse weather conditions, such as dense fog, heavy rain, high winds, etc. Adverse weather is often tiring to work in and c
©Always keep a firm grip on the saw with your right hand on the rear handle, your left handonthe front handle, and with yourthumbsandfingersencirclin
WARNING! A majority of kickback accidents occur during iimbing. Do not use the nose of the guide bar. Be extremeiy cautious and avoid contacting t
©Basic rules for felling treesNormally the felling consists of two main cutting operations — notching and making the felling cut.Start making the uppe
0 Felling cut, trunk diameter less than guide bar lengthSaw either with a pushing chain (top of guide bar)... or with a pulling chain (bottom of guide
0 LimbingLimbing is removing the branches trom a felled tree.WARNING! A majority of kickback accidents occur during limbing. Do not use the noseof the
Dieser Text stimmt mit den Ansprüchen der deutschen Behörden überein.WichtigVor Gebrauch der Motorsäge sollten Sie unbedingt diese Bedienungsan
0 Cross cutting/buckingBefore starting to cut through the log, try to imagine what is going to happen. Lock out for stresses in the log and cut throug
0 If the saw gets stuckStop the engine.Raise the log or change its position, using a thick branch or pole as a lever.Do not try to pull the saw free.
©Common senseWe have already pointed out that a chain saw is a dangerous tool, if used carelessly, or if improperly maintained.If you use your chain s
Traduction française des précautions de sécurité générales.AvertissementToutes les personnes qui utiliseront cette tronçonneusedevraient lire ce manue
©Technical specificationEngineDisplacement Bore Stroke Idling speedRecommended max speed unloaded Ignition systemManufacturer/type of ign. systemSpark
© ©©What is whatEinzelteileLes éléments deon the sawder Motorsägela tronçonneuse1. Cylinder cover.1. Zylinderdeckel.1. Capot de cylindre.2. Front hand
0 Mounting guide bar and chainCheck that the chain brake is in disengaged position by moving the front hand guard backwards.Take off the bar nuts and
Locate the chain adjuster pin in the hole on the bar. Check that the drive links of the chain fit correctly on the drive sprocket and that the chain i
Comments to this Manuals