114 00 07-26250PSOperator's manualRead these instructions carefully and make sureyou understand them before using the saw.
10 – EnglishSAFETY INSTRUCTIONSD. Correction of raker clearanceChain lubricationWARNING!A slack chain may jump off and causeserious or even fatal inju
English – 11SAFETY INSTRUCTIONSWARNING!Defective cutting equipment can increasethe risk for accidents.Check regularly the degreeof wear on the drive w
12 – EnglishSAFETY INSTRUCTIONSGeneral safety instructionsIMPORTANT INFORMATION• The machine is only designed for tree pruning.• The only accessories
English – 13SAFETY INSTRUCTIONS2. Avoid usage in un-favourable weather conditions. Forexample, thick fog, heavy rain, strong winds or extremecold, etc
14 – EnglishSAFETY INSTRUCTIONSBasic clearing techniques• Always work with the engine at full throttle.• Always drop to idling speed after each workin
English – 15WHAT IS WHAT?14. Throttle control15. Guide bar16. Adjuster screw for oilvolume to chain17. Telescopic shaft18. Hydraulic motor19. Chain20.
16 – EnglishASSEMBLYWARNING!The cutting equipment of the pruning sawmay under no circumstances be connectedto another type of hydraulic pump thanwhat
English – 17FUEL HANDLINGFuel mixMixing• Always mix the petrol and oil in a clean container intendedfor fuel.• Always start by filling half the amount
18 – EnglishFUEL HANDLING – START AND STOPStart and stop• Clean around the fuel cap.Contamination in thetank can disrupt opera-tions.• Ensure that the
English – 19START AND STOPFitting theharness• Put on the harness withengine unit.• Press together the hipbelt’s snap lock.• Tension the hip belt sotha
2 – EnglishSymbolsSwitch off the engine by moving thestop switch to the STOP positionbefore carrying out any checks ormaintenance.Always wear approved
20 – EnglishMAINTENANCEWARNING!Contact your servicing dealer, if the idlespeed setting cannot be adjusted. Do notuse the pruner until it has been prop
English – 21MAINTENANCEAir filterThe air filters must be regularly cleaned from dust and dirt inorder to avoid: • Carburettor malfunctions • Starting
22 – EnglishMAINTENANCECooling systemTo maintain as low anoperating temperature aspossible the engine isequipped with a coolingsystem.The cooling syst
English – 23MAINTENANCEMonthlymaintenance1.Clean the fuel tank usingpetrol.2.Clean the carburettor andthe space surrounding it.3.Clean the fan and the
24 – EnglishTECHNICAL DATAVibration levelsEquivalent sound pressure levelas per ISO 7505 max. output speed,unloaded engine.Left (shaft) idling/max. ou
English – 25TECHNICAL DATAType Inch Inch/mm Inch/mm Angle Angle Angle Inch/mm Inch/cm: dl90 SG 3/8" 0,028"/1,1 5/32" /4,0 85° 30° 0° 0
26 – English´+HÆh¶6v¨EU declaration of conformity (Only applies to Europe)(Directive 89/392/EEC, Annex II, A)We, Husqvarna AB, S-561 82 Huskvarna, Swe
English – 27
28 – English´+HÆh¶6v¨2001W14
English – 3CONTENTSSYMBOL EXPLANATIONSymbols...2CONTENTSContents...
4 – EnglishThe machine's safety equipmentThis section describes the machine's safety equipment, itsfunction and how checks and maintenance a
English – 55. SilencerThe silencer is designed togive the lowest possible noiselevel and to direct theengine's exhaust fumes awayfrom the operato
6 – EnglishControl, maintenance and service ofthe machine's safety equipment1. Throttle trigger lock• Check that the throttle islocked in the
English – 7A. Only use cuttingequipmentrecommended by us!See the ”Technical data”section.B. Keep the chain cuttingteeth properlysharpened! Follow ouri
8 – EnglishSAFETY INSTRUCTIONSSharpening your chain andadjusting raker clearanceWARNING!The risk of kickback is increased with abadly sharpened chain!
English – 9SAFETY INSTRUCTIONSIt is very difficult to sharpen achain correctly without theright equipment. We recom-mend you to use a file gauge.This
Comments to this Manuals