EEEEnnnngggglllliiiisssshhhhK650 Cut-n-BreakOperator’s manual (EPA)Please read the operator’s manual carefully and make sure you understand the instru
10 – EnglishSAFETY INSTRUCTIONSBlade vibrationsThe blades can become out of true and vibrate if a too high feed pressure is used.A lower feed pressure
English – 11SAFETY INSTRUCTIONS• Cut in the same direction when cutting into an existing cut. Avoid cutting at an angle to the previous cut otherwise
12 – EnglishSAFETY INSTRUCTIONSGeneral rules• Never cut upwards or towards you so that the kickback zone becomes actively cutting.• Always hold the ma
English – 13ASSEMBLYAssembling the bladesHusqvarna blades are especially manufactured and approved for freehand cutting with the K650 Cut-n-Break. The
14 – EnglishFUEL HANDLINGFuelCAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-st
English – 15STARTING AND STOPPINGBefore startingWater connectorConnect the water hose to the water supply. The water flow is regulated using the water
16 – EnglishMAINTENANCEInspecting and adjusting the drive belt• The drive belt is fully enclosed and well-protected from dust, dirt and mechanical dam
English – 17MAINTENANCE• Pull off the cutting arm by pulling it straight forwards, as illustrated.• Remove the complete drive belt (D).• Loosen the si
18 – EnglishMAINTENANCEAir filterAir filters must be regularly cleaned to remove dust and dirt in order to avoid:• Carburettor malfunctions• Starting pr
English – 19MAINTENANCEStarterChanging a broken or worn starter cord• Loosen the filter and cylinder cover.• Loosen the screws that hold the starter ag
2 – EnglishKEY TO SYMBOLSSymbols on the machine:WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause seriou
20 – EnglishMAINTENANCEChanging a broken recoil spring• Undo the bolt in the centre of the pulley and remove the pulley.• Bear in mind that the return
English – 21MAINTENANCECooling systemTo keep the working temperature as low as possible the machine is equipped with a cooling system.The cooling syst
22 – EnglishTECHNICAL DATA´®z+SNQ¶5[¨´®z+SNQ¶5[¨Technical dataCutting equipmentMax. blade speed, rpm6200K650 Cut-n-breakEngineCylinder displacement, c
English – 23FEDERAL EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme
´®z+SNQ¶5[¨2009-01-10´®z+SNQ¶5[¨1151464-95!WARNING! Cutting, especially when DRY cutting, generates dust that comes from the material being cut, which
English – 3CONTENTSContentsKEY TO SYMBOLSSymbols on the machine: ... 2Symbols in the operator’s manual: ...
4 – EnglishWHAT IS WHAT?What is what on the power cutter?HUSQVARNA CONSTRUCTION PRODUCTS1 Operator’s manual (EPA)2 Combination spanner3 Air filter cove
English – 5SAFETY INSTRUCTIONSSteps before using a new power cutter• Please read the operator’s manual carefully and make sure you understand the inst
6 – EnglishSAFETY INSTRUCTIONSGeneral safety precautionsWork area safety• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
English – 7SAFETY INSTRUCTIONSFuel safety(Refuelling/Fuel mixture/Storage.)• Never refuel the machine while the engine is running.• Make sure there is
8 – EnglishSAFETY INSTRUCTIONSCAUTION! Never use a machine that has a faulty muffler.Throttle lockoutThe throttle trigger lock is designed to prevent a
English – 9SAFETY INSTRUCTIONSThrottle lockout• Make sure the throttle control is locked at the idle setting when the throttle lockout is released.• P
Comments to this Manuals